• Frister Rossmann Manual

Frister+Rossmann Cub 3 & 4 Sewing Machine Instruction Manual Immediate Download PDF---Click On Image To Enlarge. More Frister+Rossmann Manuals NEXT PAGE.

Frister Rossmann Manual

THE NEEDLEBAR Online Manuals Section I N S T R U C T I O N S FOR THE USE OF FRISTER AND ROSSMANN'S Automatic Chainstitch Sewing Machines PART TWO SETTING THE NEEDLE The needle has a continuous groove running from the end of the eye, and the end of the Needle Bar has a corresponding mark upon which the groove fits and slides; the object is to ensure the Needle being properly placed, namely, with the groove always to the left; and any attempt to force in a Needle without a groove, or with the groove in the wrong direction, will result in. Fastening the Needle large wheel; then, holding the Needle between the thumb and first finger )Fig. 5) with the groove towards the left, insert the point of the Needle Hole in the Cloth Plate until the shank of the Needle is able to be inserted into the opening in the Needle Bar. Holding the Needle Wrench ( A) provided (Fig.

7) between the right thumb and first finger, gradually turn the Needle Bar Nut ( B) to the right, until the Needle is firmly bedded in its place. Do not use a blunt needle; as it cannot do good work, and is liable to bend or break in going through the material. Never use a bent needle; it will cause dropped stitches and damage the Looper. TO TAKE OUT THE NEEDLE Let down the Presser Foot and raise the Needle Bar to its highest point. Unscrew the Needle Bar Nut with Needle Wrench, by making a quarter turn to the left.

• View & download of more than 3 Frister & rossmann PDF user manuals, service manuals, operating guides. Sewing machine, user manuals, operating guides & specifications.
• Frister Cub 7 - Download as PDF File (.pdf). INSTRUCTION MANUAL. Frister + Rossmann Sewing Machines, Limited.

TO TIGHTEN THE STRAP When the Strap requires tightening, which it may do after the machine has been some time in use, proceed as follows:- Take off the Strap, cut a small piece off one end, make a fresh hole, and again connect the ends by means of the hook. TO THREAD THE MACHINE The Threading of the Machine is shown in Fig.1. Huawei software installing stuck. In Threading, first pull out the Spool Pin, and place the Reel upon it. Replace Spool Pin. Raise the Needle Bar to its highest point, by turning large Wheel, and then proceed as follows: 1. Thread from the back toward you, through the two staples and hole in lever known as Pull-off (1, Fig.1).

Pull through about six inches of thread. It facilitates threading to double and twist the end of the thread, it can be more readily passed through Pull-off and following places, when threading. Then carry the thread between the Reel and Automatic Tension, drawing the thread into the slot under the cap of tension (2, Fig. Thread from right to left through the Thread Pin on top of the Frame (3, Fig.1). Take the Thread from right to left through Wire Staple (4, Fig.1). Do not thread through loop of Spring under this Staple, unless embroidering. Take the thread between thumb and finger of both hands, passing it between the Needle Bar and Take-up, and press it from you into the opening at the top of the Take-up (5, Fig.1) 6.

Take the thread downwards through the Thread Pin (6, Fig.1). Then through the Needle Eye from left to right (Fig.1).

TO REGULATE LENGTH OF STITCH TO SIZE OF THREAD OR SILK USED.

ISMACS is an organization totally independent of all sewing-machine manufacturers, past or present and is not affiliated with any of the companies mentioned in these pages. Please Note: Do not contact any ISMACS official in an attempt to solicit a valuation - it is not possible other than by hands-on assessment and your request will be ignored. All rights reserved by ISMACS INTERNATIONAL, under International and Pan American copyright conventions. Reproduction or copy of this page, in any form, in part or in whole, is strictly prohibited, without prior, written permission.